搜索资源列表
ModBussource.rar
- 用于PLC或RTU上的MODBUS 通信代码,可以作为MODBUS程序开发参考,For the PLC or RTU
MODBUS-CSharp
- socket测试小程序。MODBUS协议。很简单的小例子，适合初学者。-socket test applet. MODBUS protocol. A very simple little example for beginners.
Modbus_FCS.rar
- modbus ascii RTU 的校验码计算程序 VC++6.0,modbus ascii RTU checksum calculation program code VC++6.0
ModBus_rs485_send
- 基于dspic33f单片机，RS485硬件的ModBus通讯协议程序，初始状态为发送-Based on dspic33f microcontroller, RS485 ModBus communication protocol program the hardware, the initial state to send
modbus_main
- ModBus主站程序 KEIL C51，51单片机实现-ModBus master program KEIL C51, 51 MCU
atmega88MODBUS
- MODBUS的atmega88的程序。从国外网站下载后，稍加修改而成，使用WINAVR2010和AVRSTuDIO编译，通过修改参数也可用在atmega其他的MCU-MODBUS' s atmega88 procedures. After downloading from abroad, made a little modification, use WINAVR2010 and AVRSTuDIO compiled by modifying the parameters used in
modbus
- 为modbus的slave的处理程序，通过这部分可以看出功能码的实现-modbus slave， very good, for your use de
ModbusVCprcess
- 基于VC的MODBUS通信实现程序，界面用的是文档/视图结构，能与数据库相连、绘制响应图形等，可参考上传的论文ModbusVC-VC-based implementation of the MODBUS communications program interface using a document/view architecture, can be connected with the database, drawing responses graphics, etc., may refer
ModbusActiveX
- MODBUS RTU ActiveX控件VB6演示程序-MODBUS RTU ActiveX Control VB6 demo program
BIANPIN
- S7-300PLC与变频器通过485串口的通讯例子程序-S7-300PLC and converter serial communications through the 485 examples of the procedures
FreeModbus_uCOS
- 本程序基于STM32F103VET6，成功的将FreeModbus 和 uC/OSII 移植上去。Modbus（Rtu RS232 从机）。有问题请与我联系！QQ：383016632。-The program is based on STM32F103VET6, the success of the FreeModbus and uC/OSII transplantation up. Modbus (Rtu RS232 from the machine). There are problems
VB--CRC
- 使用VB程序编写的一个简单实用的CRC校验器，绝对好用，使用Modbus通信协议的可以下载-VB programmers use a simple check of the CRC, and the absolute ease of use, use the Modbus communication protocol can be downloaded to see if
modscan
- 一个特别好的modbus从机扫描程序，可以以RTU或ASCII方式通信以此来检验下位机。-A particularly good modbus slave scanner can communicate with RTU or ASCII way to test this lower position.
Modbus_CVI71
- modbus主站与从站发送接收程序。基于labwindows/cvi编译环境-modbus master and slave sending and receiving procedures. Based on labwindows/cvi build environment
S7-1200_winsock_new_1PLC
- vb与西门子plc的modbus tcp通讯程序-vb and Siemens plc, modbus tcp communication program
modbusRTU_C51_RS485
- modbus RTU 的C51程序 单片机89S52 通信波特率 9600 8位数据 1位停止位 偶校验 485通位接口 单片机控制板地址 localAddr(变量) 通信可设置数据的地址： 字地址 0 - 255 (只取16位的低8位) 位地址 0 - 255 (只取16位的低8位)-modbus RTU' s C51 program microcontroller 89S52 Communication baud rate 96008 bits of d
modbus
- modbus串口通信，利用vc6.0控件自己的项目中用到的代码，很好用。里面有两个程序，一个上位机，一个模仿下位的极的程序，可以互相通信。-modbus serial communication, the use the code the vc6.0 controls used in the project, to very good use. There are two programs, a host computer, an imitation of a bit extreme progr
16led
- 6个16*16的LED点阵，内含PROTUES仿真图和单片机程序-6 16* 16 LED dot-matrix
modbus-51
- 此程序是51单片机的串口的测试程序，采用modbus通信协议，包括接收，发送，与主测试程序等-This program is 51 single-chip serial port test program, using modbus communication protocols, including receiving, sending, and the main test procedures
2812dsp-Sci
- 这是一个基于DSP2812的串口通讯下位机程序,通过该程序可以实现和上位机通讯,将上位机的数据读入,设置电机的转矩和转速.挺好的一个程序,供参考.-This is a serial communication based on the DSP2812-bit machine under the procedures, the adoption of the procedures can be achieved and the host computer communications, will